Linux/CC2650: Unable to see [bbbb::100] website running contiki-NG

Hi, I have indeed followed steps 3.6-3.8.

From a clean raspberry jessie lite  install i do the following:

from "Setup 6lbr to run 6LowPAN with CC2531 USB dongle on Raspberry Pi 2B"

3. sudo apt-get install libncurses5-dev
4. sudo apt-get install bridge-utils

6. git clone --recursive

7. cd 6lbr/examples/6lbr

8. make all plugins tools ---> This step takes lots of time so go for a break!

9. sudo make install

10. Create /etc/6lbr/6lbr.conf with the content below

     MODE=ROUTER

     RAW_ETH=1

     BRIDGE=0

     DEV_BRIDGE=br0

     DEV_TAP=tap0

     DEV_ETH=eth0

     RAW_ETH_FCS=0

     DEV_RADIO=/dev/ttyACM0

     BAUDRATE=115200

     LOG_LEVEL=3

If i do not follow these steps, I can not run "nvm_tool" in the following 3.6-3.8:

from: Build and run 6lbr/Contiki-NG cc26xx-web-demo on Rasperry Pi with LAUNCHXL-CC1310/LAUNCHXL-CC2650

3.3 Change directory to 6lbr folder and git checkout contiki-ng

3.4 Change directory to home folder and git clone --recursive

3.5 Change directory to contiki-ng folder and git checkout sixlbr

3.6 Change directory to 6lbr/examples/6lbr folder and run the following build command

"make WITH_CONTIKI=0 CONTIKI=../../../contiki-ng all"

3.6  After build successfully, do "sudo make install". You will see "install: cannot stat ‘tools/nvm_tool’: No such file or directory" issue since nvm_tool doens't make properly for current version. It might be fixed later but you can use nvm_tool built by previous 6lbr to do the following steps.

3.7 Run "sudo /usr/lib/6lbr/bin/nvm_tool --update --channel 25 /etc/6lbr/nvm.dat" to change 6lbr/Contiki-NG to use channel 25.

3.8 Run "/usr/lib/6lbr/bin/nvm_tool --print /etc/6lbr/nvm.dat" to make sure it switches to channel 25.

When i have done this, i do not get the error you mention in 3.6, but i still do 3.7 and 3.8 successfully. What am i doing wrong? 

I have repeated the steps from a clean install a couple of times today and this is what my log looks like now:

Yes, i followed the steps in the order posted above.  Should i instead git clone contiki-ng, git checkout sixlbr, and then do "make all plugins tools"? Or which order do i follow?

I have followed the steps exactly from the two posts, except i don't do:

"5. sudo vi /boot/cmdline.txt file and add the following configuration parameter in the beginning of cmdline.txt 

dwc_otg.speed=1"

because it ish breaks SSH (I can only be connected ~20 sec before it hangs). And instead of : "$/usr/lib/6lbr/bin/nvm_tool --update --channel 25 /etc/6lbr/nvm.dat"  I do it with sudo because of permission.

Still, in "3.6  After build successfully, do "sudo make install". You will see "install: cannot stat ‘tools/nvm_tool’: No such file or directory" issue since nvm_tool doens't make properly for current version. It might be fixed later but you can use nvm_tool built by previous 6lbr to do the following steps." I don't see any error, it just compiles fine.

My 6lbr.log i still see "CONFIG: Can not open /etc/6lbr/nvm.conf : No such file or directory".

Is there anything else i'm missing? I'm using a clean debian jesse lite installation every try on RPI 2 with wifi dongle.

It's not being created. I've tried both "make all plugins tools" and "make TARGET=native all plugins tools" before running "sudo /usr/lib/6lbr/bin/nvm_tool --update --channel 25 /etc/6lbr/nvm.dat".

Any suggestions on how to create nvm.conf?

This is my /etc/6lbr folder.

I have tried building without contiki-NG with a cc2531 slip radio and it still doesn't work. Worth mentioning is that i never see [ok] starting 6lowpan border router. I'm giving up on this unless you know anything else, and i'll try later when i have an ethernet cable instead of wifi dongle and mobile hotspot.