IEC 61851-23-2014 Electric vehicle conductive charging system - Part 23 D.C electric vehicle charging station《电动车辆传导式充电系统 第23部分 直流电动车辆充电站》.pdf

《IEC 61851-23-2014 Electric vehicle conductive charging system - Part 23 D.C electric vehicle charging station《电动车辆传导式充电系统 第23部分 直流电动车辆充电站》.pdf》由会员分享，可在线阅读，更多相关《IEC 61851-23-2014 Electric vehicle conductive charging system - Part 23 D.C electric vehicle charging station《电动车辆传导式充电系统 第23部分 直流电动车辆充电站》.pdf（164页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 61851-23 Edition 1.0 2014-03 INTERNATIONAL STANDARD NORME INTERNATIONALE Electric vehicle conductive charging system Part 23: DC electric vehicle charging station Systme de charge conductive pour vhicules lectriques Partie 23: Borne de charge en courant continu pour vhicules lectriques IEC 6185

2、1-23:2014-03(en-fr) colour inside THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2014 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying a

3、nd microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC me

4、mber National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans

5、laccord crit de lIEC ou du Comit national de lIEC du pays du demandeur. Si vous avez des questions sur le copyright de lIEC ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de lIEC de votre pays de rsidence. IEC

6、 Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrica

7、l, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. IEC Catalogue - webstore.iec.ch/catalogue The

8、stand-alone application for consulting the entire bibliographical information on IEC International Standards, Technical Specifications, Technical Reports and other documents. Available for PC, Mac OS, Android Tablets and iPad. IEC publications search - www.iec.ch/searchpub The advanced search enable

9、s to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all n

10、ew publications released. Available online and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivalent terms in 14 additional langu

11、ages. Also known as the International Electrotechnical Vocabulary (IEV) online. IEC Glossary - std.iec.ch/glossary More than 55 000 electrotechnical terminology entries in English and French extracted from the Terms and Definitions clause of IEC publications issued since 2002. Some entries have been

12、 collected from earlier publications of IEC TC 37, 77, 86 and CISPR. IEC Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. A propos de lIEC La Commission Electrotec

13、hnique Internationale (IEC) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications IEC Le contenu technique des publications IEC est constamment revu. Veuillez vo

14、us assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue IEC - webstore.iec.ch/catalogue Application autonome pour consulter tous les renseignements bibliographiques sur les Normes internationales, Spcifications techniques, Rapports techniques et

15、 autres documents de lIEC. Disponible pour PC, Mac OS, tablettes Android et iPad. Recherche de publications IEC - www.iec.ch/searchpub La recherche avance permet de trouver des publications IEC en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations

16、 sur les projets et les publications remplaces ou retires. IEC Just Published - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications IEC. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.elect

17、ropedia.org Le premier dictionnaire en ligne de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans 14 langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (IEV) en ligne. Glos

18、saire IEC - std.iec.ch/glossary Plus de 55 000 entres terminologiques lectrotechniques, en anglais et en franais, extraites des articles Termes et Dfinitions des publications IEC parues depuis 2002. Plus certaines entres antrieures extraites des publications des CE 37, 77, 86 et CISPR de lIEC. Servi

19、ce Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 61851-23 Edition 1.0 2014-03 INTERNATIONAL STANDARD NORME INTERNATIONALE Electric vehicle conductive charging system Part 23: DC electric ve

20、hicle charging station Systme de charge conductive pour vhicules lectriques Partie 23: Borne de charge en courant continu pour vhicules lectriques INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE XC ICS 43.120 PRICE CODE CODE PRIX ISBN 978-2-8322-1440-4 Registered

21、 trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur

22、agr. colour inside 2 IEC 61851-23:2014 IEC 2014 CONTENTS FOREWORD . 4 INTRODUCTION . 6 1 Scope 7 2 Normative references 7 3 Terms and definitions 8 4 General requirements 10 5 Rating of the supply a.c. voltage 10 6 General system requirement and interface. 10 7 Protection against electric shock . 18

23、 8 Connection between the power supply and the EV. 19 9 Specific requirements for vehicle coupler . 20 10 Charging cable assembly requirements . 21 11 EVSE requirements . 21 101 Specific requirements for d.c. EV charging station . 24 102 Communication between EV and d.c. EV charging station . 29 Ann

24、ex AA (normative) DC EV charging station of system A 33 Annex BB (normative) DC EV charging station of system B 47 Annex CC (normative) DC EV charging station of system C (Combined charging system) . 55 Annex DD (informative) Typical d.c. charging systems 70 Annex EE (informative) Typical configurat

25、ion of d.c. charging system . 75 Bibliography 76 Figure 101 Overvoltage protection in case of earth fault 16 Figure 102 Measuring network of touch current weighted for perception or reaction . 23 Figure 103 Step response for constant value control 26 Figure 104 Current ripple measurement equipment w

26、ith capacitor . 27 Figure 105 Maximum ratings for voltage dynamics . 28 Figure AA.1 Overall schematic of system A station and EV 34 Figure AA.2 Interface circuit for charging control of system A station . 35 Figure AA.3 Failure detection principle by detection of d.c. leakage current . 38 Figure AA.

27、4 Example of vehicle connector latch and lock monitoring circuit . 40 Figure AA.5 State transition diagram of charging process for system A 43 Figure AA.6 Sequence diagram of system A 44 Figure AA.7 Charging current value requested by the vehicle 45 Figure AA.8 Output response performance of d.c. EV

28、 charging station . 46 Figure BB.1 Schematic diagram for basic solution for d.c. charging system . 47 Figure BB.2 Sequence diagram of charging process 52 Figure BB.3 Operation flow chart of start charging . 53 Figure BB.4 Operation flow chart of stop charging . 54 Figure CC.1 Sequence diagram for no

29、rmal start up 57 IEC 61851-23:2014 IEC 2014 3 Figure CC.2 Sequence diagram and description for normal shutdown 59 Figure CC.3 Sequence diagram for d.c. supply initiated emergency shutdown . 61 Figure CC.4 Sequence diagram for EV initiated emergency shutdown 63 Figure CC.5 Special components for conf

30、igurations CC and EE coupler 66 Figure CC.6 System schematics of combined d.c. charging system 68 Figure D.1 Example of typical isolated system . 70 Figure D.2 Example of typical non-isolated system 71 Figure D.3 Example of simplified isolated system . 71 Figure D.4 Example of DC mains system . 72 F

31、igure E.1 Typical configuration of d.c. charging system 75 Table 101 Current ripple limit of d.c. EV charging station . 27 Table 102 Charging state of d.c. EV charging station . 30 Table 103 Charging control process of d.c. EV charging station at system action level 31 Table AA.1 Definition of symbo

32、ls in Figure AA.1 and Figure AA.2 36 Table AA.2 Parameters and values for interface circuit in Figure AA.2 . 37 Table AA.3 Principle of fault protection 37 Table AA.4 Requirements for earth fault monitoring . 39 Table AA.5 Recommended specification of charging current requested by the vehicle . 45 T

33、able AA.6 Requirements for the output response performance of d.c. EV charging station 45 Table BB.1 Definitions of charging states . 50 Table BB.2 Recommended parameters of d.c. charging security system 51 Table CC.1 DC couplers and maximum system output voltage for combined charging system 55 Tabl

34、e CC.2 Definition of proximity resistor for configurations DD and FF . 55 Table CC.3 Sequence description for normal start up . 58 Table CC.4 Sequence description for normal shutdown . 60 Table CC.5 Definition and description of symbols / terms . 69 Table D.1 Example for categories of d.c. supply sy

35、stem to electric vehicles . 73 Table D.2 Typical voltage ranges for isolated d.c. EV charging stations . 74 4 IEC 61851-23:2014 IEC 2014 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ ELECTRIC VEHICLE CONDUCTIVE CHARGING SYSTEM Part 23: DC electric vehicle charging station FOREWORD 1) The International

36、 Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fi

37、elds. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any I

38、EC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardiz

39、ation (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has represe

40、ntation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC c

41、annot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publicat

42、ions. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas,

43、access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including

44、individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance u

45、pon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the element

46、s of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61851-23 has been prepared by IEC technical committee 69: Electric road vehicles and electric industrial trucks. The text of this

47、 standard is based on the following documents: FDIS Report on voting 69/272/FDIS 69/279/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives,

48、 Part 2. This standard is to be read in conjunction with IEC 61851-1:2010. It was established on the basis of the second edition (2010) of that standard. IEC 61851-23:2014 IEC 2014 5 The clauses of particular requirements in this standard supplement or modify the corresponding clauses in IEC 61851-1

49、:2010. Where the text of subsequent clauses indicates an “addition“ to or a “replacement“ of the relevant requirement, test specification or explanation of Part 1, these changes are made to the relevant text of Part 1, which then becomes part of this standard. Where no change is necessary, the words “This clause of Part 1 is applicable“ are used. Additional cla